TRAK Site Information Form International GPS Service See Instructions at: ftp://igscb.jpl.nasa.gov/pub/station/general/sitelog_instr.txt 0. Form Prepared by (full name) : Paul Jamason Date Prepared : 2000-07-15 Report Type : DYNAMIC If Update: Previous Site Log : trak0007.log Modified/Added Sections : (n.n,n.n,...) 1. Site Identification of the GNSS Monument Site Name : Bommer Canyon Four Character ID : TRAK Monument Inscription : IERS DOMES Number : 40480M001 CDP Number : (A4) Monument Description : (PILLAR/BRASS PLATE/STEEL MAST/etc) Height of the Monument : (m) Monument Foundation : (STEEL RODS, CONCRETE BLOCK, ROOF, etc) Foundation Depth : (m) Marker Description : (CHISELLED CROSS/DIVOT/BRASS NAIL/etc) Date Installed : 1994-06-02T00:00Z Geologic Characteristic : (BEDROCK/CLAY/CONGLOMERATE/GRAVEL/SAND/etc) Bedrock Type : (IGNEOUS/METAMORPHIC/SEDIMENTARY) Bedrock Condition : (FRESH/JOINTED/WEATHERED) Fracture Spacing : (1-10 cm/10-50 cm/50-200 cm/over 200 cm) Fault zones nearby : (YES/NO/Name of the zone) Distance/activity : (multiple lines) Additional Information : (multiple lines) : SCIGN - Southern California Integrated GPS : Network single 5/8 in. diameter, 14 in. : stainless steel rod driven into sandstone rock : outcropping : Geodetic reference point is punched hole in : top of rod. : Monument model code is . 2. Site Location Information City or Town : Irvine State or Province : California Country : USA Tectonic Plate : North America Pacific Approximate Position (ITRF) X coordinate (m) : -2480029.12 Y coordinate (m) : -4703110.98 Z coordinate (m) : 3511298.51 Latitude (N is +) : +333712.00 Longitude (E is +) : -1174760.00 Elevation (m,ellips.) : 115.56 Additional Information : Located in Bommer Canyon : Orange County. : Reference frame used is (ITRF97). : Coordinate system used is (WGS84). 3. GNSS Receiver Information 3.1 Receiver Type : ASHTECH Z-XII3 Satellite System : (GPS/GLONASS/GPS+GLONASS) Serial Number : 03233 Firmware Version : NAV 1C01, CHN 1C00 Elevation Cutoff Setting : (deg) Date Installed : 1994-06-02T00:00Z Date Removed : 1994-09-12T00:00Z Temperature Stabiliz. : (none or tolerance in degrees C) Additional Information : First measurements 3.2 Receiver Type : ASHTECH Z-XII3 Satellite System : (GPS/GLONASS/GPS+GLONASS) Serial Number : 02684 Firmware Version : NAV 1D00, CHN 1C01 Elevation Cutoff Setting : (deg) Date Installed : 1994-09-12T00:00Z Date Removed : 1994-11-11T00:00Z Temperature Stabiliz. : (none or tolerance in degrees C) Additional Information : New receiver (1Mb of memory) 3.3 Receiver Type : ASHTECH Z-XII3 Satellite System : (GPS/GLONASS/GPS+GLONASS) Serial Number : 04673 Firmware Version : NAV 1E00, CHN 1C50 Elevation Cutoff Setting : (deg) Date Installed : 1994-11-11T00:00Z Date Removed : 1995-12-21T00:00Z Temperature Stabiliz. : (none or tolerance in degrees C) Additional Information : New receiver, firmware (6Mb of memory) : 30 meter Belden 8214 RG-8 antenna cable : AC Power with UPS backup 3.4 Receiver Type : ASHTECH Z-XII3 Satellite System : (GPS/GLONASS/GPS+GLONASS) Serial Number : 03015 Firmware Version : 1E76 Elevation Cutoff Setting : (deg) Date Installed : 1995-12-21T00:00Z Date Removed : 1996-01-10T00:00Z Temperature Stabiliz. : (none or tolerance in degrees C) Additional Information : 3.5 Receiver Type : ASHTECH Z-XII3 Satellite System : (GPS/GLONASS/GPS+GLONASS) Serial Number : 03015 Firmware Version : 1G00 Elevation Cutoff Setting : (deg) Date Installed : 1996-01-10T00:00Z Date Removed : 1996-04-11T00:00Z Temperature Stabiliz. : (none or tolerance in degrees C) Additional Information : 3.6 Receiver Type : ASHTECH Z-XII3 Satellite System : (GPS/GLONASS/GPS+GLONASS) Serial Number : 03015 Firmware Version : 1E81 Elevation Cutoff Setting : (deg) Date Installed : 1996-04-11T00:00Z Date Removed : 1996-05-16T00:00Z Temperature Stabiliz. : (none or tolerance in degrees C) Additional Information : 3.7 Receiver Type : ASHTECH Z-XII3 Satellite System : (GPS/GLONASS/GPS+GLONASS) Serial Number : 03015 Firmware Version : 1E86 Elevation Cutoff Setting : (deg) Date Installed : 1996-05-16T00:00Z Date Removed : 1996-08-16T00:00Z Temperature Stabiliz. : (none or tolerance in degrees C) Additional Information : 3.8 Receiver Type : ASHTECH Z-XII3 Satellite System : (GPS/GLONASS/GPS+GLONASS) Serial Number : 03015 Firmware Version : 1E95 Elevation Cutoff Setting : (deg) Date Installed : 1996-08-16T00:00Z Date Removed : 1997-12-03T00:00Z Temperature Stabiliz. : (none or tolerance in degrees C) Additional Information : 3.9 Receiver Type : ASHTECH Z-XII3 Satellite System : (GPS/GLONASS/GPS+GLONASS) Serial Number : 03015 Firmware Version : 1F50 Elevation Cutoff Setting : (deg) Date Installed : 1997-12-03T00:00Z Date Removed : 1999-07-09T18:10Z Temperature Stabiliz. : (none or tolerance in degrees C) Additional Information : New receiver, firmware, for SCIGN expansion : and met pack install : ASHTECH Z-XII3 (Z12) Model 700845-10(F) 3.10 Receiver Type : ASHTECH Z-XII3 Satellite System : (GPS/GLONASS/GPS+GLONASS) Serial Number : LP03110 Firmware Version : CC00 Elevation Cutoff Setting : (deg) Date Installed : 1999-07-09T18:10Z Date Removed : (CCYY-MM-DDThh:mmZ) Temperature Stabiliz. : (none or tolerance in degrees C) Additional Information : Receiver swap/upgrade for GPS week : rollover compliance 3.x Receiver Type : (A20, from rcvr_ant.tab; see instructions) Satellite System : (GPS/GLONASS/GPS+GLONASS) Serial Number : (A5) Firmware Version : (A11) Elevation Cutoff Setting : (deg) Date Installed : (CCYY-MM-DDThh:mmZ) Date Removed : (CCYY-MM-DDThh:mmZ) Temperature Stabiliz. : (none or tolerance in degrees C) Additional Information : (multiple lines) 4. GNSS Antenna Information 4.1 Antenna Type : ASH700228A Serial Number : 700228D2406 Antenna Reference Point : BPA Marker->ARP Up Ecc. (m) : 0.6069 Marker->ARP North Ecc(m) : (F8.4) Marker->ARP East Ecc(m) : (F8.4) Alignment from True N : Antenna Radome Type : SNOW Radome Serial Number : Antenna Cable Type : (vendor & type number) Antenna Cable Length : (m) Date Installed : 1994-06-02T00:00Z Date Removed : 1994-11-11T00:00Z Additional Information : (multiple lines) 4.2 Antenna Type : ASH700228A Serial Number : 10537 Antenna Reference Point : BPA Marker->ARP Up Ecc. (m) : 0.6080 Marker->ARP North Ecc(m) : (F8.4) Marker->ARP East Ecc(m) : (F8.4) Alignment from True N : Antenna Radome Type : SNOW Radome Serial Number : Antenna Cable Type : (vendor & type number) Antenna Cable Length : (m) Date Installed : 1994-11-11T00:00Z Date Removed : 1995-08-03T00:00Z Additional Information : (multiple lines) 4.3 Antenna Type : ASH700228A Serial Number : 10537 Antenna Reference Point : BPA Marker->ARP Up Ecc. (m) : 0.6080 Marker->ARP North Ecc(m) : (F8.4) Marker->ARP East Ecc(m) : (F8.4) Alignment from True N : Antenna Radome Type : SNOW Radome Serial Number : Antenna Cable Type : (vendor & type number) Antenna Cable Length : (m) Date Installed : 1995-08-03T00:00Z Date Removed : 1995-08-04T00:00Z Additional Information : site enclosure dome currently in use, : no code applicable 4.4 Antenna Type : ASH700936B_M Serial Number : CR11936 Antenna Reference Point : BPA Marker->ARP Up Ecc. (m) : 0.5370 Marker->ARP North Ecc(m) : (F8.4) Marker->ARP East Ecc(m) : (F8.4) Alignment from True N : Antenna Radome Type : ENCL Radome Serial Number : Antenna Cable Type : (vendor & type number) Antenna Cable Length : (m) Date Installed : 1995-08-04T00:00Z Date Removed : (CCYY-MM-DDThh:mmZ) Additional Information : Radome removed - Site enclosure in use : Rinex headers should be changed from : 'NONE' to 'ENCL' up to 08/11/1999 4.x Antenna Type : (A20, from rcvr_ant.tab; see instructions) Serial Number : (A*, but note the first A5 is used in SINEX) Antenna Reference Point : (BPA/BCR/XXX from "antenna.gra"; see instr.) Marker->ARP Up Ecc. (m) : (F8.4) Marker->ARP North Ecc(m) : (F8.4) Marker->ARP East Ecc(m) : (F8.4) Alignment from True N : (deg; + is clockwise/east) Antenna Radome Type : (A4 from rcvr_ant.tab; see instructions) Radome Serial Number : Antenna Cable Type : (vendor & type number) Antenna Cable Length : (m) Date Installed : (CCYY-MM-DDThh:mmZ) Date Removed : (CCYY-MM-DDThh:mmZ) Additional Information : (multiple lines) 5. Surveyed Local Ties 5.x Tied Marker Name : Tied Marker Usage : (SLR/VLBI/LOCAL CONTROL/FOOTPRINT/etc) Tied Marker CDP Number : (A4) Tied Marker DOMES Number : (A9) Differential Components from GNSS Marker to the tied monument (ITRS) dx (m) : dy (m) : dz (m) : Accuracy (mm) : (mm) Survey method : (GPS CAMPAIGN/TRILATERATION/TRIANGULATION/etc) Date Measured : (CCYY-MM-DDThh:mmZ) Additional Information : (multiple lines) 6. Frequency Standard 6.1 Standard Type : INTERNAL Input Frequency : Effective Dates : 1994-06-02/CCYY-MM-DD Notes : (multiple lines) 6.x Standard Type : (INTERNAL or EXTERNAL H-MASER/CESIUM/etc) Input Frequency : (if external) Effective Dates : (CCYY-MM-DD/CCYY-MM-DD) Notes : (multiple lines) 7. Collocation Information 7.x Instrumentation Type : (GPS/GLONASS/DORIS/PRARE/SLR/VLBI/TIME/etc) Status : (PERMANENT/MOBILE) Effective Dates : (CCYY-MM-DD/CCYY-MM-DD) Notes : (multiple lines) 8. Meteorological Instrumentation 8.1.1 Humidity Sensor Model : MET3 Manufacturer : Paroscientific Serial Number : Data Sampling Interval : 600 sec. Accuracy (% rel h) : 2. Aspiration : (UNASPIRATED/NATURAL/FAN/etc) Height Diff to Ant : (m) Calibration date : (CCYY-MM-DD) Effective Dates : 2000-07-12/CCYY-MM-DD Notes : replaced bad unit; SN unknown 8.1.x Humidity Sensor Model : Manufacturer : Serial Number : Data Sampling Interval : (sec) Accuracy (% rel h) : (% rel h) Aspiration : (UNASPIRATED/NATURAL/FAN/etc) Height Diff to Ant : (m) Calibration date : (CCYY-MM-DD) Effective Dates : (CCYY-MM-DD/CCYY-MM-DD) Notes : (multiple lines) 8.2.1 Pressure Sensor Model : MET3 Manufacturer : Paroscientific Serial Number : Data Sampling Interval : 600 sec. Accuracy : .5 Height Diff to Ant : (m) Calibration date : (CCYY-MM-DD) Effective Dates : 2000-07-12/CCYY-MM-DD Notes : pj replaced bad unit 8.2.x Pressure Sensor Model : Manufacturer : Serial Number : Data Sampling Interval : (sec) Accuracy : (hPa) Height Diff to Ant : (m) Calibration date : (CCYY-MM-DD) Effective Dates : (CCYY-MM-DD/CCYY-MM-DD) Notes : (multiple lines) 8.3.1 Temp. Sensor Model : MET3 Manufacturer : Paroscientific Serial Number : Data Sampling Interval : 600 sec. Accuracy : .5 Aspiration : (UNASPIRATED/NATURAL/FAN/etc) Height Diff to Ant : (m) Calibration date : (CCYY-MM-DD) Effective Dates : 2000-07-12/CCYY-MM-DD Notes : pj replaced bad unit 8.3.x Temp. Sensor Model : Manufacturer : Serial Number : Data Sampling Interval : (sec) Accuracy : (hPa) Aspiration : (UNASPIRATED/NATURAL/FAN/etc) Height Diff to Ant : (m) Calibration date : (CCYY-MM-DD) Effective Dates : (CCYY-MM-DD/CCYY-MM-DD) Notes : (multiple lines) 8.4.1 Water Vapor Radiometer : Manufacturer : Serial Number : Distance to Antenna : (m) Height Diff to Ant : (m) Calibration date : (CCYY-MM-DD) Effective Dates : CCYY-MM-DD/CCYY-MM-DD Notes : (multiple lines) 8.4.x Water Vapor Radiometer : Manufacturer : Serial Number : Distance to Antenna : (m) Height Diff to Ant : (m) Calibration date : (CCYY-MM-DD) Effective Dates : (CCYY-MM-DD/CCYY-MM-DD) Notes : (multiple lines) 8.5.1 Other Instrumentation : 8.5.x Other Instrumentation : 9. Local Ongoing Conditions Possibly Affecting Computed Position 9.1.x Radio Interferences : (TV/CELL PHONE ANTENNA/RADAR/etc) Observed Degredations : (SN RATIO/DATA GAPS/etc) Effective Dates : (CCYY-MM-DD/CCYY-MM-DD) Additional Information : (multiple lines) 9.2.x Multipath Sources : (METAL ROOF/DOME/VLBI ANTENNA/etc) Effective Dates : (CCYY-MM-DD/CCYY-MM-DD) Additional Information : (multiple lines) 9.3.x Signal Obstructions : (TREES/BUILDLINGS/etc) Effective Dates : (CCYY-MM-DD/CCYY-MM-DD) Additional Information : (multiple lines) 10. Local Episodic Effects Possibly Affecting Data Quality 10.x Date : (CCYY-MM-DD/CCYY-MM-DD) Event : (TREE CLEARING/CONSTRUCTION/etc) 11. On-Site, Point of Contact Agency Information Agency : Scripps Orbit and Permanent Array Center Preferred Abbreviation : (A10) Mailing Address : Institute of Geophysics and Planetary Physics, : Scripps Institution of Oceanography, MC 0225, : University of California San Diego, 9500 : Gilman Dr., La Jolla CA 92093-0225 Primary Contact Contact Name : Paul F. Jamason Telephone (primary) : 858-534-1750 Telephone (secondary) : 858-534-7692 Fax : 858-534-9873 E-mail : pjamason@lox.ucsd.edu Secondary Contact Contact Name : John Galetzka Telephone (primary) : 626-583-7230 Telephone (secondary) : 626-583-7816 Fax : 626-583-7827 E-mail : galetzka@gps.caltech.edu Additional Information : (multiple lines) 12. Responsible Agency (if different from 11.) Agency : (multiple lines) Preferred Abbreviation : (A10) Mailing Address : (multiple lines) Primary Contact Contact Name : Telephone (primary) : Telephone (secondary) : Fax : E-mail : Secondary Contact Contact Name : Telephone (primary) : Telephone (secondary) : Fax : E-mail : Additional Information : (multiple lines) 13. More Information URL for More Information : Hardcopy on File Site Map : (Y or URL) Site Diagram : (Y) Horizon Mask : (Y) Monument Description : (Y) Site Pictures : (Y) Additional Information : (multiple lines) Antenna Graphics with Dimensions (insert text graphic)