International GPS Service PIN1 Site Information Form See Instructions at: ftp://igscb.jpl.nasa.gov/pub/station/general/sitelog_instr.txt 0. Form Prepared by (full name) : Paul Jamason Date Prepared : 2001-08-22 Report Type : DYNAMIC If Update: Previous Site Log : pin10108.log Modified/Added Sections : (n.n,n.n,...) 1. Site Identification of the GNSS Monument Site Name : Pinyon 1 Four Character ID : PIN1 Monument Inscription : PFO 1989 UCSD IGPP IERS DOMES Number : 40407M003 CDP Number : (A4) Monument Description : (PILLAR/BRASS PLATE/STEEL MAST/etc) Height of the Monument : (m) Monument Foundation : (STEEL RODS, CONCRETE BLOCK, ROOF, etc) Foundation Depth : (m) Marker Description : (CHISELLED CROSS/DIVOT/BRASS NAIL/etc) Date Installed : 1990-02-09T00:00Z Geologic Characteristic : (BEDROCK/CLAY/CONGLOMERATE/GRAVEL/SAND/etc) Bedrock Type : (IGNEOUS/METAMORPHIC/SEDIMENTARY) Bedrock Condition : (FRESH/JOINTED/WEATHERED) Fracture Spacing : (1-10 cm/10-50 cm/50-200 cm/over 200 cm) Fault zones nearby : (YES/NO/Name of the zone) Distance/activity : (multiple lines) Additional Information : (multiple lines) : SCIGN - Southern California Integrated GPS : Network. Removable fixed height tripod, : kinematically positioned above a ground level : mark embedded in a concrete pad, the pad is : anchored by nine 32' deep drilled and cemented : legs, to achieve both positional and : rotational stability, the latter is essential : so tilts don't cause the tripod to tilt. : Adaptor rests on flat plate where monument : legs join. : Geodetic reference point is disk in concrete : pad. : Monument model is removeable tripod / concrete : pad. 2. Site Location Information City or Town : Pinyon Flat State or Province : California Country : USA Tectonic Plate : North America Pacific Approximate Position (ITRF) X coordinate (m) : -2369510.55 Y coordinate (m) : -4761207.12 Z coordinate (m) : 3511396.21 Latitude (N is +) : +333636.00 Longitude (E is +) : -1162736.00 Elevation (m,ellips.) : 1256.21 Additional Information : Pinon Flat Observatory : Riverside County. : Reference frame used is (ITRF97). : Coordinate system used is (WGS84). 3. GNSS Receiver Information 3.1 Receiver Type : TRIMBLE 4000SST Satellite System : (GPS/GLONASS/GPS+GLONASS) Serial Number : 496 Firmware Version : 4.11 Elevation Cutoff Setting : (deg) Date Installed : 1990-02-09T00:00Z Date Removed : 1990-02-14T00:00Z Temperature Stabiliz. : (none or tolerance in degrees C) Additional Information : First measurements 3.2 Receiver Type : TRIMBLE 4000SST Satellite System : (GPS/GLONASS/GPS+GLONASS) Serial Number : 422 Firmware Version : 4.11 Elevation Cutoff Setting : (deg) Date Installed : 1990-02-14T00:00Z Date Removed : 1990-03-15T00:00Z Temperature Stabiliz. : (none or tolerance in degrees C) Additional Information : Site ties 05-MAR-1990 3.3 Receiver Type : ROGUE SNR-8 Satellite System : (GPS/GLONASS/GPS+GLONASS) Serial Number : Scripps ROGUE Firmware Version : 2.3 Elevation Cutoff Setting : (deg) Date Installed : 1990-03-15T00:00Z Date Removed : 1990-03-31T00:00Z Temperature Stabiliz. : (none or tolerance in degrees C) Additional Information : Records data with UTC time tags 3.4 Receiver Type : ROGUE SNR-8 Satellite System : (GPS/GLONASS/GPS+GLONASS) Serial Number : Scripps ROGUE Firmware Version : 2.31 Elevation Cutoff Setting : (deg) Date Installed : 1990-03-31T00:00Z Date Removed : 1990-06-19T00:00Z Temperature Stabiliz. : (none or tolerance in degrees C) Additional Information : Records data with UTC time tags 3.5 Receiver Type : ROGUE SNR-8 Satellite System : (GPS/GLONASS/GPS+GLONASS) Serial Number : JPL ROGUE Firmware Version : 5.60 Elevation Cutoff Setting : (deg) Date Installed : 1990-06-19T00:00Z Date Removed : 1991-02-15T00:00Z Temperature Stabiliz. : (none or tolerance in degrees C) Additional Information : 3.6 Receiver Type : ASHTECH LM-XII3 Satellite System : (GPS/GLONASS/GPS+GLONASS) Serial Number : 825 Firmware Version : 5F Elevation Cutoff Setting : (deg) Date Installed : 1991-02-15T00:00Z Date Removed : 1991-05-11T00:00Z Temperature Stabiliz. : (none or tolerance in degrees C) Additional Information : 3.7 Receiver Type : ASHTECH LM-XII3 Satellite System : (GPS/GLONASS/GPS+GLONASS) Serial Number : 825 Firmware Version : 1.0 Elevation Cutoff Setting : (deg) Date Installed : 1991-05-11T00:00Z Date Removed : 1991-06-30T00:00Z Temperature Stabiliz. : (none or tolerance in degrees C) Additional Information : 3.8 Receiver Type : ROGUE SNR-8 Satellite System : (GPS/GLONASS/GPS+GLONASS) Serial Number : JPL ROGUE Firmware Version : 5.60 Elevation Cutoff Setting : (deg) Date Installed : 1991-06-30T00:00Z Date Removed : 1991-10-24T00:00Z Temperature Stabiliz. : (none or tolerance in degrees C) Additional Information : 3.9 Receiver Type : ROGUE SNR-8 Satellite System : (GPS/GLONASS/GPS+GLONASS) Serial Number : SCRIPPS ROGUE Firmware Version : 5.60 Elevation Cutoff Setting : (deg) Date Installed : 1991-10-24T00:00Z Date Removed : 1992-04-25T00:00Z Temperature Stabiliz. : (none or tolerance in degrees C) Additional Information : 3.10 Receiver Type : ROGUE SNR-8 Satellite System : (GPS/GLONASS/GPS+GLONASS) Serial Number : SCRIPPS ROGUE Firmware Version : 7.0 Elevation Cutoff Setting : (deg) Date Installed : 1992-04-25T00:00Z Date Removed : 1992-09-25T00:00Z Temperature Stabiliz. : (none or tolerance in degrees C) Additional Information : 3.11 Receiver Type : ASHTECH P-XII3 Satellite System : (GPS/GLONASS/GPS+GLONASS) Serial Number : 700363B1426 Firmware Version : 6M Elevation Cutoff Setting : (deg) Date Installed : 1992-09-25T00:00Z Date Removed : 1993-06-22T00:00Z Temperature Stabiliz. : (none or tolerance in degrees C) Additional Information : 3.12 Receiver Type : ROGUE SNR-8 Satellite System : (GPS/GLONASS/GPS+GLONASS) Serial Number : SCRIPPS ROGUE Firmware Version : 7.30 Elevation Cutoff Setting : (deg) Date Installed : 1993-06-22T00:00Z Date Removed : 1993-08-18T00:00Z Temperature Stabiliz. : (none or tolerance in degrees C) Additional Information : Six good tracking channels (out of eight). : Antenna temporarily displaced on 10-AUG-1993 : 22:45-23:58 UT : 17-AUG-1993 22:00 UT 3.13 Receiver Type : TRIMBLE 4000SST Satellite System : (GPS/GLONASS/GPS+GLONASS) Serial Number : TBD Firmware Version : 4.64 Elevation Cutoff Setting : (deg) Date Installed : 1993-08-18T00:00Z Date Removed : 1993-08-19T00:00Z Temperature Stabiliz. : (none or tolerance in degrees C) Additional Information : Survey ties with PIN2 & 7256 3.14 Receiver Type : ROGUE SNR-8 Satellite System : (GPS/GLONASS/GPS+GLONASS) Serial Number : SCRIPPS ROGUE Firmware Version : 7.30 Elevation Cutoff Setting : (deg) Date Installed : 1993-08-19T00:00Z Date Removed : 1993-10-23T00:00Z Temperature Stabiliz. : (none or tolerance in degrees C) Additional Information : 3.15 Receiver Type : ROGUE SNR-8 Satellite System : (GPS/GLONASS/GPS+GLONASS) Serial Number : SCRIPPS ROGUE Firmware Version : 7.50 Elevation Cutoff Setting : (deg) Date Installed : 1993-10-23T00:00Z Date Removed : 1993-11-06T00:00Z Temperature Stabiliz. : (none or tolerance in degrees C) Additional Information : 3.16 Receiver Type : ASHTECH Z-XII3 Satellite System : (GPS/GLONASS/GPS+GLONASS) Serial Number : 700570A03001 Firmware Version : 1B10 Elevation Cutoff Setting : (deg) Date Installed : 1993-11-06T00:00Z Date Removed : 1994-01-26T00:00Z Temperature Stabiliz. : (none or tolerance in degrees C) Additional Information : 3.17 Receiver Type : ASHTECH Z-XII3 Satellite System : (GPS/GLONASS/GPS+GLONASS) Serial Number : 03207 Firmware Version : 1C01-1C00 Elevation Cutoff Setting : (deg) Date Installed : 1994-01-26T00:00Z Date Removed : 1995-08-02T00:00Z Temperature Stabiliz. : (none or tolerance in degrees C) Additional Information : 3.18 Receiver Type : ASHTECH Z-XII3 Satellite System : (GPS/GLONASS/GPS+GLONASS) Serial Number : 03207 Firmware Version : 1E00-1C50 Elevation Cutoff Setting : (deg) Date Installed : 1995-08-02T00:00Z Date Removed : 1995-11-11T00:00Z Temperature Stabiliz. : (none or tolerance in degrees C) Additional Information : Firmware Upgrade 3.19 Receiver Type : ASHTECH Z-XII3 Satellite System : (GPS/GLONASS/GPS+GLONASS) Serial Number : 03207 Firmware Version : 1E76-1D01 Elevation Cutoff Setting : (deg) Date Installed : 1995-11-11T00:00Z Date Removed : 1996-02-21T00:00Z Temperature Stabiliz. : (none or tolerance in degrees C) Additional Information : Firmware Upgrade 3.20 Receiver Type : ASHTECH Z-XII3 Satellite System : (GPS/GLONASS/GPS+GLONASS) Serial Number : 03207 Firmware Version : 1E81-1D01 Elevation Cutoff Setting : (deg) Date Installed : 1996-02-21T00:00Z Date Removed : 1996-12-19T00:00Z Temperature Stabiliz. : (none or tolerance in degrees C) Additional Information : Firmware Upgrade 3.21 Receiver Type : ASHTECH Z-XII3 Satellite System : (GPS/GLONASS/GPS+GLONASS) Serial Number : 03207 Firmware Version : 1E95-1D01 Elevation Cutoff Setting : (deg) Date Installed : 1996-12-19T00:00Z Date Removed : 1997-01-23T00:00Z Temperature Stabiliz. : (none or tolerance in degrees C) Additional Information : Firmware Upgrade 3.22 Receiver Type : ASHTECH Z-XII3 Satellite System : (GPS/GLONASS/GPS+GLONASS) Serial Number : LP01391 Firmware Version : 1E95-1D01 Elevation Cutoff Setting : (deg) Date Installed : 1997-01-23T00:00Z Date Removed : 1997-01-24T00:00Z Temperature Stabiliz. : (none or tolerance in degrees C) Additional Information : Pinon Ties 3.23 Receiver Type : ASHTECH Z-XII3 Satellite System : (GPS/GLONASS/GPS+GLONASS) Serial Number : 03207 Firmware Version : 1E95-1D01 Elevation Cutoff Setting : (deg) Date Installed : 1997-01-24T00:00Z Date Removed : 1998-06-23T00:00Z Temperature Stabiliz. : (none or tolerance in degrees C) Additional Information : Replaced after 1-day survey 3.24 Receiver Type : ASHTECH Z-XII3 Satellite System : (GPS/GLONASS/GPS+GLONASS) Serial Number : 02780 Firmware Version : 1F50 Elevation Cutoff Setting : (deg) Date Installed : 1998-06-23T00:00Z Date Removed : 1999-07-13T18:15Z Temperature Stabiliz. : (none or tolerance in degrees C) Additional Information : Swapped previous for SCIGN receiver ASHTECH : Z-XII 700845-10E 3.25 Receiver Type : ASHTECH Z-XII3 Satellite System : (GPS/GLONASS/GPS+GLONASS) Serial Number : LP02973 Firmware Version : CC00 Elevation Cutoff Setting : (deg) Date Installed : 1999-07-13T18:15Z Date Removed : (CCYY-MM-DDThh:mmZ) Temperature Stabiliz. : (none or tolerance in degrees C) Additional Information : Receiver swap for GPS week rollover compliance. 3.x Receiver Type : (A20, from rcvr_ant.tab; see instructions) Satellite System : (GPS/GLONASS/GPS+GLONASS) Serial Number : (A5) Firmware Version : (A11) Elevation Cutoff Setting : (deg) Date Installed : (CCYY-MM-DDThh:mmZ) Date Removed : (CCYY-MM-DDThh:mmZ) Temperature Stabiliz. : (none or tolerance in degrees C) Additional Information : (multiple lines) 4. GNSS Antenna Information 4.1 Antenna Type : TRM14532.00 Serial Number : TBD Antenna Reference Point : BPA Marker->ARP Up Ecc. (m) : 1.9030 Marker->ARP North Ecc(m) : (F8.4) Marker->ARP East Ecc(m) : (F8.4) Alignment from True N : 0 Antenna Radome Type : NONE Radome Serial Number : Antenna Cable Type : (vendor & type number) Antenna Cable Length : (m) Date Installed : 1990-02-09T00:00Z Date Removed : 1990-03-15T00:00Z Additional Information : (multiple lines) 4.2 Antenna Type : AOAD/M_B Serial Number : TBD Antenna Reference Point : BCR Marker->ARP Up Ecc. (m) : 1.8435 Marker->ARP North Ecc(m) : (F8.4) Marker->ARP East Ecc(m) : (F8.4) Alignment from True N : 0 Antenna Radome Type : NONE Radome Serial Number : Antenna Cable Type : (vendor & type number) Antenna Cable Length : (m) Date Installed : 1990-03-15T00:00Z Date Removed : 1991-02-15T00:00Z Additional Information : PJ changed ARP from BPA, 10-MAR-1999 4.3 Antenna Type : ASH700228A Serial Number : TBD Antenna Reference Point : BPA Marker->ARP Up Ecc. (m) : 1.8435 Marker->ARP North Ecc(m) : (F8.4) Marker->ARP East Ecc(m) : (F8.4) Alignment from True N : 0 Antenna Radome Type : NONE Radome Serial Number : Antenna Cable Type : (vendor & type number) Antenna Cable Length : (m) Date Installed : 1991-02-15T00:00Z Date Removed : 1991-06-30T00:00Z Additional Information : PJ changed install date from "15-FEB-1990", : 10-MAR-1999 4.4 Antenna Type : AOAD/M_B Serial Number : TBD Antenna Reference Point : BCR Marker->ARP Up Ecc. (m) : 1.8435 Marker->ARP North Ecc(m) : (F8.4) Marker->ARP East Ecc(m) : (F8.4) Alignment from True N : 0 Antenna Radome Type : NONE Radome Serial Number : Antenna Cable Type : (vendor & type number) Antenna Cable Length : (m) Date Installed : 1991-06-30T00:00Z Date Removed : 1992-09-25T00:00Z Additional Information : PJ changed ARP from BPA, 10-MAR-1999 4.5 Antenna Type : ASH700228D Serial Number : 700328A0703 Antenna Reference Point : BPA Marker->ARP Up Ecc. (m) : 1.8435 Marker->ARP North Ecc(m) : (F8.4) Marker->ARP East Ecc(m) : (F8.4) Alignment from True N : 0 Antenna Radome Type : NONE Radome Serial Number : Antenna Cable Type : (vendor & type number) Antenna Cable Length : (m) Date Installed : 1992-09-25T00:00Z Date Removed : 1993-06-22T00:00Z Additional Information : 4.6 Antenna Type : AOAD/M_B Serial Number : TBD Antenna Reference Point : BCR Marker->ARP Up Ecc. (m) : 1.8435 Marker->ARP North Ecc(m) : (F8.4) Marker->ARP East Ecc(m) : (F8.4) Alignment from True N : 0 Antenna Radome Type : NONE Radome Serial Number : Antenna Cable Type : (vendor & type number) Antenna Cable Length : (m) Date Installed : 1993-06-22T00:00Z Date Removed : 1993-08-18T00:00Z Additional Information : Antenna temporarily displaced on 10-AUG-1993 : 22:45-23:58 UT. PJ changed ARP from BPA, : 10-MAR-1999 4.7 Antenna Type : TRM14532.00 Serial Number : TBD Antenna Reference Point : BPA Marker->ARP Up Ecc. (m) : 1.8435 Marker->ARP North Ecc(m) : (F8.4) Marker->ARP East Ecc(m) : (F8.4) Alignment from True N : 0 Antenna Radome Type : NONE Radome Serial Number : Antenna Cable Type : (vendor & type number) Antenna Cable Length : (m) Date Installed : 1993-08-18T00:00Z Date Removed : 1993-08-19T00:00Z Additional Information : Survey ties with PIN2 & 7256 4.8 Antenna Type : AOAD/M_B Serial Number : TBD Antenna Reference Point : BCR Marker->ARP Up Ecc. (m) : 1.8435 Marker->ARP North Ecc(m) : (F8.4) Marker->ARP East Ecc(m) : (F8.4) Alignment from True N : 0 Antenna Radome Type : NONE Radome Serial Number : Antenna Cable Type : (vendor & type number) Antenna Cable Length : (m) Date Installed : 1993-08-19T00:00Z Date Removed : 1993-11-06T00:00Z Additional Information : PJ changed ARP from BPA, 10-MAR-1999 4.9 Antenna Type : ASH700228D Serial Number : 700228D2616 Antenna Reference Point : BPA Marker->ARP Up Ecc. (m) : 1.8435 Marker->ARP North Ecc(m) : (F8.4) Marker->ARP East Ecc(m) : (F8.4) Alignment from True N : 0 Antenna Radome Type : NONE Radome Serial Number : Antenna Cable Type : (vendor & type number) Antenna Cable Length : (m) Date Installed : 1993-11-06T00:00Z Date Removed : 1995-09-02T00:00Z Additional Information : 4.10 Antenna Type : JPLD/M_RA_SOP Serial Number : F101 Antenna Reference Point : BCR Marker->ARP Up Ecc. (m) : 1.8450 Marker->ARP North Ecc(m) : (F8.4) Marker->ARP East Ecc(m) : (F8.4) Alignment from True N : 0 Antenna Radome Type : NONE Radome Serial Number : Antenna Cable Type : (vendor & type number) Antenna Cable Length : (m) Date Installed : 1995-09-02T00:00Z Date Removed : 1997-01-23T00:00Z Additional Information : PJ changed ARP from BPA, 10-MAR-1999 4.11 Antenna Type : ASH700936D_M Serial Number : 12655 Antenna Reference Point : BPA Marker->ARP Up Ecc. (m) : 1.790 Marker->ARP North Ecc(m) : (F8.4) Marker->ARP East Ecc(m) : (F8.4) Alignment from True N : 0 Antenna Radome Type : NONE Radome Serial Number : Antenna Cable Type : (vendor & type number) Antenna Cable Length : (m) Date Installed : 1997-01-23T00:00Z Date Removed : 1997-01-24T00:00Z Additional Information : Pinon Ties. Log formerly stated direct : height of 1.134 m, corrected based on : physical measurement at site 4.12 Antenna Type : JPLD/M_RA_SOP Serial Number : F101 Antenna Reference Point : BCR Marker->ARP Up Ecc. (m) : 1.845 Marker->ARP North Ecc(m) : (F8.4) Marker->ARP East Ecc(m) : (F8.4) Alignment from True N : 0 Antenna Radome Type : NONE Radome Serial Number : Antenna Cable Type : (vendor & type number) Antenna Cable Length : (m) Date Installed : 1997-01-24T00:00Z Date Removed : 2001-02-28T00:00Z Additional Information : Replaced after 1-day survey. Antenna modified : for ASHTECH. PJ changed ARP from BPA, : 10-MAR-1999 4.13 Antenna Type : ASH701945C_M Serial Number : CR620005001 Antenna Reference Point : BPA Marker->ARP Up Ecc. (m) : 1.790 Marker->ARP North Ecc(m) : (F8.4) Marker->ARP East Ecc(m) : (F8.4) Alignment from True N : 0 Antenna Radome Type : SCIS Radome Serial Number : Antenna Cable Type : (vendor & type number) Antenna Cable Length : (m) Date Installed : 2001-02-28T00:00Z Date Removed : (CCYY-MM-DDThh:mmZ) Additional Information : Height was 1.745, corrected based on : physical measurement at site. It is presumed : that the previous model has a bad set of : antenna dimensions, and that the : old height for this antenna, which was : based on the previous model minus the : removed antenna adaptor, was incorrect. : Dome serial number is 208. 4.x Antenna Type : (A20, from rcvr_ant.tab; see instructions) Serial Number : (A*, but note the first A5 is used in SINEX) Antenna Reference Point : (BPA/BCR/XXX from "antenna.gra"; see instr.) Marker->ARP Up Ecc. (m) : (F8.4) Marker->ARP North Ecc(m) : (F8.4) Marker->ARP East Ecc(m) : (F8.4) Alignment from True N : (deg; + is clockwise/east) Antenna Radome Type : (A4 from rcvr_ant.tab; see instructions) Radome Serial Number : Antenna Cable Type : (vendor & type number) Antenna Cable Length : (m) Date Installed : (CCYY-MM-DDThh:mmZ) Date Removed : (CCYY-MM-DDThh:mmZ) Additional Information : (multiple lines) 5. Surveyed Local Ties 5.1 Tied Marker Name : 7256 NCMN 1981 Tied Marker Usage : (SLR/VLBI/LOCAL CONTROL/FOOTPRINT/etc) Tied Marker CDP Number : 204 Tied Marker DOMES Number : 40407M001 Differential Components from GNSS Marker to the tied monument (ITRS) dx (m) : -125.588 dy (m) : -117.655 dz (m) : -279.91 Accuracy (mm) : 1 Survey method : (GPS CAMPAIGN/TRILATERATION/TRIANGULATION/etc) Date Measured : 1990-03-05T00:00Z Additional Information : Post Landers/Big Bear earthquakes 28-JUN-1993 5.2 Tied Marker Name : Pinyon 2 Tied Marker Usage : (SLR/VLBI/LOCAL CONTROL/FOOTPRINT/etc) Tied Marker CDP Number : Tied Marker DOMES Number : 40407M004 Differential Components from GNSS Marker to the tied monument (ITRS) dx (m) : 44.038 dy (m) : -24.468 dz (m) : .438 Accuracy (mm) : 1 Survey method : (GPS CAMPAIGN/TRILATERATION/TRIANGULATION/etc) Date Measured : 1990-03-05T00:00Z Additional Information : Post Landers/Big Bear earthquakes 28-JUN-1993 5.x Tied Marker Name : Tied Marker Usage : (SLR/VLBI/LOCAL CONTROL/FOOTPRINT/etc) Tied Marker CDP Number : (A4) Tied Marker DOMES Number : (A9) Differential Components from GNSS Marker to the tied monument (ITRS) dx (m) : dy (m) : dz (m) : Accuracy (mm) : (mm) Survey method : (GPS CAMPAIGN/TRILATERATION/TRIANGULATION/etc) Date Measured : (CCYY-MM-DDThh:mmZ) Additional Information : (multiple lines) 6. Frequency Standard 6.1 Standard Type : INTERNAL Input Frequency : Effective Dates : 1990-01-09/CCYY-MM-DD Notes : ROGUE SNR-8 uses external rubidium standard 6.x Standard Type : (INTERNAL or EXTERNAL H-MASER/CESIUM/etc) Input Frequency : (if external) Effective Dates : (CCYY-MM-DD/CCYY-MM-DD) Notes : (multiple lines) 7. Collocation Information 7.1 Instrumentation Type : VLBI Status : MOBILE Effective Dates : (CCYY-MM-DD/CCYY-MM-DD) Notes : (multiple lines) 7.x Instrumentation Type : (GPS/GLONASS/DORIS/PRARE/SLR/VLBI/TIME/etc) Status : (PERMANENT/MOBILE) Effective Dates : (CCYY-MM-DD/CCYY-MM-DD) Notes : (multiple lines) 8. Meteorological Instrumentation 8.1.1 Humidity Sensor Model : Manufacturer : Serial Number : Data Sampling Interval : Accuracy (% rel h) : (% rel h) Aspiration : (UNASPIRATED/NATURAL/FAN/etc) Height Diff to Ant : (m) Calibration date : (CCYY-MM-DD) Effective Dates : CCYY-MM-DD/CCYY-MM-DD Notes : (multiple lines) 8.1.x Humidity Sensor Model : Manufacturer : Serial Number : Data Sampling Interval : (sec) Accuracy (% rel h) : (% rel h) Aspiration : (UNASPIRATED/NATURAL/FAN/etc) Height Diff to Ant : (m) Calibration date : (CCYY-MM-DD) Effective Dates : (CCYY-MM-DD/CCYY-MM-DD) Notes : (multiple lines) 8.2.1 Pressure Sensor Model : Manufacturer : Serial Number : Data Sampling Interval : Accuracy : (mbar) Height Diff to Ant : (m) Calibration date : (CCYY-MM-DD) Effective Dates : CCYY-MM-DD/CCYY-MM-DD Notes : (multiple lines) 8.2.x Pressure Sensor Model : Manufacturer : Serial Number : Data Sampling Interval : (sec) Accuracy : (hPa) Height Diff to Ant : (m) Calibration date : (CCYY-MM-DD) Effective Dates : (CCYY-MM-DD/CCYY-MM-DD) Notes : (multiple lines) 8.3.1 Temp. Sensor Model : Manufacturer : Serial Number : Data Sampling Interval : Accuracy : (deg C) Aspiration : (UNASPIRATED/NATURAL/FAN/etc) Height Diff to Ant : (m) Calibration date : (CCYY-MM-DD) Effective Dates : CCYY-MM-DD/CCYY-MM-DD Notes : (multiple lines) 8.3.x Temp. Sensor Model : Manufacturer : Serial Number : Data Sampling Interval : (sec) Accuracy : (hPa) Aspiration : (UNASPIRATED/NATURAL/FAN/etc) Height Diff to Ant : (m) Calibration date : (CCYY-MM-DD) Effective Dates : (CCYY-MM-DD/CCYY-MM-DD) Notes : (multiple lines) 8.4.1 Water Vapor Radiometer : Manufacturer : Serial Number : Distance to Antenna : (m) Height Diff to Ant : (m) Calibration date : (CCYY-MM-DD) Effective Dates : CCYY-MM-DD/CCYY-MM-DD Notes : (multiple lines) 8.4.x Water Vapor Radiometer : Manufacturer : Serial Number : Distance to Antenna : (m) Height Diff to Ant : (m) Calibration date : (CCYY-MM-DD) Effective Dates : (CCYY-MM-DD/CCYY-MM-DD) Notes : (multiple lines) 8.5.1 Other Instrumentation : 8.5.x Other Instrumentation : 9. Local Ongoing Conditions Possibly Affecting Computed Position 9.1.x Radio Interferences : (TV/CELL PHONE ANTENNA/RADAR/etc) Observed Degredations : (SN RATIO/DATA GAPS/etc) Effective Dates : (CCYY-MM-DD/CCYY-MM-DD) Additional Information : (multiple lines) 9.2.x Multipath Sources : (METAL ROOF/DOME/VLBI ANTENNA/etc) Effective Dates : (CCYY-MM-DD/CCYY-MM-DD) Additional Information : (multiple lines) 9.3.x Signal Obstructions : (TREES/BUILDLINGS/etc) Effective Dates : (CCYY-MM-DD/CCYY-MM-DD) Additional Information : (multiple lines) 10. Local Episodic Effects Possibly Affecting Data Quality 10.x Date : (CCYY-MM-DD/CCYY-MM-DD) Event : (TREE CLEARING/CONSTRUCTION/etc) 11. On-Site, Point of Contact Agency Information Agency : Scripps Orbit and Permanent Array Center Preferred Abbreviation : (A10) Mailing Address : Institute of Geophysics and Planetary Physics, : Scripps Institution of Oceanography, MC 0225, : University of California San Diego, 9500 : Gilman Dr., La Jolla CA 92093-0225 Primary Contact Contact Name : Paul F. Jamason Telephone (primary) : 858-534-1750 Telephone (secondary) : 858-534-7692 Fax : 858-534-9873 E-mail : pjamason@lox.ucsd.edu Secondary Contact Contact Name : John Galetzka Telephone (primary) : 626-583-7230 Telephone (secondary) : 626-583-7816 Fax : 626-583-7827 E-mail : galetzka@gps.caltech.edu Additional Information : (multiple lines) 12. Responsible Agency (if different from 11.) Agency : (multiple lines) Preferred Abbreviation : (A10) Mailing Address : (multiple lines) Primary Contact Contact Name : Telephone (primary) : Telephone (secondary) : Fax : E-mail : Secondary Contact Contact Name : Telephone (primary) : Telephone (secondary) : Fax : E-mail : Additional Information : (multiple lines) 13. More Information URL for More Information : Hardcopy on File Site Map : (Y or URL) Site Diagram : (Y) Horizon Mask : (Y) Monument Description : (Y) Site Pictures : (Y) Additional Information : (multiple lines) Antenna Graphics with Dimensions (insert text graphic)