PERT Site Information Form International GPS Service See Instructions at: ftp://igscb.jpl.nasa.gov/pub/station/general/sitelog_instr.txt 0. Form Prepared by (full name) : C.Garcia Date Prepared : 2001-06-07 Report Type : UPDATE If Update: Previous Site Log : pert0106.log Modified/Added Sections : (n.n,n.n,...) 1. Site Identification of the GNSS Monument Site Name : Perth Four Character ID : PERT Monument Inscription : None IERS DOMES Number : 50133M001 CDP Number : None Monument Description : (PILLAR/BRASS PLATE/STEEL MAST/etc) Height of the Monument : (m) Monument Foundation : (STEEL RODS, CONCRETE BLOCK, ROOF, etc) Foundation Depth : (m) Marker Description : (CHISELLED CROSS/DIVOT/BRASS NAIL/etc) Date Installed : 1993-08-18 Geologic Characteristic : (BEDROCK/CLAY/CONGLOMERATE/GRAVEL/SAND/etc) Bedrock Type : (IGNEOUS/METAMORPHIC/SEDIMENTARY) Bedrock Condition : (FRESH/JOINTED/WEATHERED) Fracture Spacing : (1-10 cm/10-50 cm/50-200 cm/over 200 cm) Fault zones nearby : (YES/NO/Name of the zone) Distance/activity : (multiple lines) Additional Information : (multiple lines) : Mark at the center of a horizontal : metal plate embedded on the concrete : monument. 2. Site Location Information City or Town : Perth State or Province : Country : Australia Tectonic Plate : Austral Approximate Position (ITRF) X coordinate (m) : -2368686.749 Y coordinate (m) : 4881316.485 Z coordinate (m) : -3341796.389 Latitude (N is +) : -314806.84 Longitude (E is +) : +1155306.72 Elevation (m,ellips.) : 12.92 Additional Information : (multiple lines) 3. GNSS Receiver Information 3.1 Receiver Type : ROGUE SNR-8100 Satellite System : (GPS/GLONASS/GPS+GLONASS) Serial Number : 108 Firmware Version : 2.8 Elevation Cutoff Setting : (deg) Date Installed : 1993-08-18 Date Removed : 1993-09-12T23:59Z Temperature Stabiliz. : (none or tolerance in degrees C) Additional Information : (multiple lines) 3.2 Receiver Type : ROGUE SNR-8100 Satellite System : (GPS/GLONASS/GPS+GLONASS) Serial Number : 105 Firmware Version : 2.8 Elevation Cutoff Setting : (deg) Date Installed : 1993-09-13 Date Removed : 1994-04-26T23:59Z Temperature Stabiliz. : (none or tolerance in degrees C) Additional Information : (multiple lines) 3.3 Receiver Type : ROGUE SNR-8100 Satellite System : (GPS/GLONASS/GPS+GLONASS) Serial Number : 108 Firmware Version : 2.8 Elevation Cutoff Setting : (deg) Date Installed : 1994-04-27 Date Removed : 1996-06-11T23:59Z Temperature Stabiliz. : (none or tolerance in degrees C) Additional Information : (multiple lines) 3.4 Receiver Type : ROGUE SNR-8100 Satellite System : (GPS/GLONASS/GPS+GLONASS) Serial Number : 108 Firmware Version : 3.2.32.1 Elevation Cutoff Setting : (deg) Date Installed : 1996-06-12 Date Removed : 1999-07-23 Temperature Stabiliz. : (none or tolerance in degrees C) Additional Information : (multiple lines) 3.5 Receiver Type : ROGUE SNR-8100 Satellite System : (GPS/GLONASS/GPS+GLONASS) Serial Number : 108 Firmware Version : 3.2.32.9 Elevation Cutoff Setting : (deg) Date Installed : 1999-07-23 Date Removed : 2001-06-06T00:00Z Temperature Stabiliz. : (none or tolerance in degrees C) Additional Information : (multiple lines) 3.6 Receiver Type : ASHTECH Z-XII3 Satellite System : (GPS/GLONASS/GPS+GLONASS) Serial Number : LP020005101 Firmware Version : NAV CD00,CHN 1D02*21 Elevation Cutoff Setting : (deg) Date Installed : 2001-06-07T00:00Z Date Removed : (CCYY-MM-DDThh:mmZ) Temperature Stabiliz. : (none or tolerance in degrees C) Additional Information : (multiple lines) 3.x Receiver Type : (A20, from rcvr_ant.tab; see instructions) Satellite System : (GPS/GLONASS/GPS+GLONASS) Serial Number : (A5) Firmware Version : (A11) Elevation Cutoff Setting : (deg) Date Installed : (CCYY-MM-DDThh:mmZ) Date Removed : (CCYY-MM-DDThh:mmZ) Temperature Stabiliz. : (none or tolerance in degrees C) Additional Information : (multiple lines) 4. GNSS Antenna Information 4.1 Antenna Type : AOAD/M_T Serial Number : 163 Antenna Reference Point : BPA Marker->ARP Up Ecc. (m) : 0.0568 Marker->ARP North Ecc(m) : (F8.4) Marker->ARP East Ecc(m) : (F8.4) Alignment from True N : Antenna Radome Type : Radome Serial Number : Antenna Cable Type : (vendor & type number) Antenna Cable Length : (m) Date Installed : 1993-08-18 Date Removed : 1993-09-12T23:59Z Additional Information : (multiple lines) 4.2 Antenna Type : AOAD/M_T Serial Number : 204 Antenna Reference Point : BPA Marker->ARP Up Ecc. (m) : 0.0568 Marker->ARP North Ecc(m) : (F8.4) Marker->ARP East Ecc(m) : (F8.4) Alignment from True N : Antenna Radome Type : Radome Serial Number : Antenna Cable Type : (vendor & type number) Antenna Cable Length : (m) Date Installed : 1993-09-13 Date Removed : 1993-09-18T23:59Z Additional Information : (multiple lines) 4.3 Antenna Type : AOAD/M_T Serial Number : 204 Antenna Reference Point : BPA Marker->ARP Up Ecc. (m) : 0.0595 Marker->ARP North Ecc(m) : (F8.4) Marker->ARP East Ecc(m) : (F8.4) Alignment from True N : Antenna Radome Type : Radome Serial Number : Antenna Cable Type : (vendor & type number) Antenna Cable Length : (m) Date Installed : 1993-09-19 Date Removed : 1994-04-26T23:59Z Additional Information : (multiple lines) 4.4 Antenna Type : AOAD/M_T Serial Number : 163 Antenna Reference Point : BPA Marker->ARP Up Ecc. (m) : 0.0595 Marker->ARP North Ecc(m) : (F8.4) Marker->ARP East Ecc(m) : (F8.4) Alignment from True N : Antenna Radome Type : Radome Serial Number : Antenna Cable Type : (vendor & type number) Antenna Cable Length : (m) Date Installed : 1994-04-27 Date Removed : 2001-06-06T00:00Z Additional Information : (multiple lines) 4.5 Antenna Type : AOAD/M_T Serial Number : 152 Antenna Reference Point : BPA Marker->ARP Up Ecc. (m) : 0.0595 Marker->ARP North Ecc(m) : (F8.4) Marker->ARP East Ecc(m) : (F8.4) Alignment from True N : Antenna Radome Type : Radome Serial Number : Antenna Cable Type : (vendor & type number) Antenna Cable Length : (m) Date Installed : 2001-06-07T00:00Z Date Removed : (CCYY-MM-DDThh:mmZ) Additional Information : (multiple lines) 4.x Antenna Type : (A20, from rcvr_ant.tab; see instructions) Serial Number : (A*, but note the first A5 is used in SINEX) Antenna Reference Point : (BPA/BCR/XXX from "antenna.gra"; see instr.) Marker->ARP Up Ecc. (m) : (F8.4) Marker->ARP North Ecc(m) : (F8.4) Marker->ARP East Ecc(m) : (F8.4) Alignment from True N : (deg; + is clockwise/east) Antenna Radome Type : (A4 from rcvr_ant.tab; see instructions) Radome Serial Number : Antenna Cable Type : (vendor & type number) Antenna Cable Length : (m) Date Installed : (CCYY-MM-DDThh:mmZ) Date Removed : (CCYY-MM-DDThh:mmZ) Additional Information : (multiple lines) 5. Surveyed Local Ties 5.x Tied Marker Name : Tied Marker Usage : (SLR/VLBI/LOCAL CONTROL/FOOTPRINT/etc) Tied Marker CDP Number : (A4) Tied Marker DOMES Number : (A9) Differential Components from GNSS Marker to the tied monument (ITRS) dx (m) : dy (m) : dz (m) : Accuracy (mm) : (mm) Survey method : (GPS CAMPAIGN/TRILATERATION/TRIANGULATION/etc) Date Measured : (CCYY-MM-DDThh:mmZ) Additional Information : (multiple lines) 6. Frequency Standard 6.1 Standard Type : CESIUM Input Frequency : Effective Dates : 1993-08-18/CCYY-MM-DD Notes : (multiple lines) 6.x Standard Type : (INTERNAL or EXTERNAL H-MASER/CESIUM/etc) Input Frequency : (if external) Effective Dates : (CCYY-MM-DD/CCYY-MM-DD) Notes : (multiple lines) 7. Collocation Information 7.x Instrumentation Type : (GPS/GLONASS/DORIS/PRARE/SLR/VLBI/TIME/etc) Status : (PERMANENT/MOBILE) Effective Dates : (CCYY-MM-DD/CCYY-MM-DD) Notes : (multiple lines) 8. Meteorological Instrumentation 8.1.1 Humidity Sensor Model : Manufacturer : Serial Number : Data Sampling Interval : Accuracy (% rel h) : (% rel h) Aspiration : (UNASPIRATED/NATURAL/FAN/etc) Height Diff to Ant : (m) Calibration date : (CCYY-MM-DD) Effective Dates : CCYY-MM-DD/CCYY-MM-DD Notes : (multiple lines) 8.1.x Humidity Sensor Model : Manufacturer : Serial Number : Data Sampling Interval : (sec) Accuracy (% rel h) : (% rel h) Aspiration : (UNASPIRATED/NATURAL/FAN/etc) Height Diff to Ant : (m) Calibration date : (CCYY-MM-DD) Effective Dates : (CCYY-MM-DD/CCYY-MM-DD) Notes : (multiple lines) 8.2.1 Pressure Sensor Model : Manufacturer : Serial Number : Data Sampling Interval : Accuracy : (mbar) Height Diff to Ant : (m) Calibration date : (CCYY-MM-DD) Effective Dates : CCYY-MM-DD/CCYY-MM-DD Notes : (multiple lines) 8.2.x Pressure Sensor Model : Manufacturer : Serial Number : Data Sampling Interval : (sec) Accuracy : (hPa) Height Diff to Ant : (m) Calibration date : (CCYY-MM-DD) Effective Dates : (CCYY-MM-DD/CCYY-MM-DD) Notes : (multiple lines) 8.3.1 Temp. Sensor Model : Manufacturer : Serial Number : Data Sampling Interval : Accuracy : (deg C) Aspiration : (UNASPIRATED/NATURAL/FAN/etc) Height Diff to Ant : (m) Calibration date : (CCYY-MM-DD) Effective Dates : CCYY-MM-DD/CCYY-MM-DD Notes : (multiple lines) 8.3.x Temp. Sensor Model : Manufacturer : Serial Number : Data Sampling Interval : (sec) Accuracy : (hPa) Aspiration : (UNASPIRATED/NATURAL/FAN/etc) Height Diff to Ant : (m) Calibration date : (CCYY-MM-DD) Effective Dates : (CCYY-MM-DD/CCYY-MM-DD) Notes : (multiple lines) 8.4.1 Water Vapor Radiometer : Manufacturer : Serial Number : Distance to Antenna : (m) Height Diff to Ant : (m) Calibration date : (CCYY-MM-DD) Effective Dates : CCYY-MM-DD/CCYY-MM-DD Notes : (multiple lines) 8.4.x Water Vapor Radiometer : Manufacturer : Serial Number : Distance to Antenna : (m) Height Diff to Ant : (m) Calibration date : (CCYY-MM-DD) Effective Dates : (CCYY-MM-DD/CCYY-MM-DD) Notes : (multiple lines) 8.5.1 Other Instrumentation : (multiple lines) 8.5.x Other Instrumentation : 9. Local Ongoing Conditions Possibly Affecting Computed Position 9.1.x Radio Interferences : (TV/CELL PHONE ANTENNA/RADAR/etc) Observed Degredations : (SN RATIO/DATA GAPS/etc) Effective Dates : (CCYY-MM-DD/CCYY-MM-DD) Additional Information : (multiple lines) 9.2.x Multipath Sources : (METAL ROOF/DOME/VLBI ANTENNA/etc) Effective Dates : (CCYY-MM-DD/CCYY-MM-DD) Additional Information : (multiple lines) 9.3.x Signal Obstructions : (TREES/BUILDLINGS/etc) Effective Dates : (CCYY-MM-DD/CCYY-MM-DD) Additional Information : (multiple lines) 10. Local Episodic Effects Possibly Affecting Data Quality 10.x Date : (CCYY-MM-DD/CCYY-MM-DD) Event : (TREE CLEARING/CONSTRUCTION/etc) 11. On-Site, Point of Contact Agency Information Agency : ESA Perth Ground Station : At ESOC Preferred Abbreviation : (A10) Mailing Address : Perth International : Telecommunications Centre : PO Box 1115At ESOC : Wangara : W.A. 6065 : Australia : 61-9-302-2000 : : 61-9-34326-71 : : : : : : : : (multiple lines) : : : : : ESA / ESOC : Robert-Bosch-Strasse 5 : D-64293 : Darmstadt : Germany Primary Contact Contact Name : J.Dow Telephone (primary) : 49-6151-902272 Telephone (secondary) : Fax : 49-6151-902271 E-mail : John.Dow@esa.int Secondary Contact Contact Name : C.Garcia Telephone (primary) : 49-6151-902088 Telephone (secondary) : Fax : 49-6151-902271 E-mail : Carlos.Garcia-Martinez@esa.int Additional Information : (multiple lines) 12. Responsible Agency (if different from 11.) Agency : (multiple lines) Preferred Abbreviation : (A10) Mailing Address : (multiple lines) Primary Contact Contact Name : Telephone (primary) : Telephone (secondary) : Fax : E-mail : Secondary Contact Contact Name : Telephone (primary) : Telephone (secondary) : Fax : E-mail : Additional Information : (multiple lines) 13. More Information URL for More Information : http://nng.esoc.esa.de/gps/perth.html Hardcopy on File Site Map : (Y or URL) Site Diagram : X Horizon Mask : (Y) Monument Description : X Site Pictures : X Additional Information : (multiple lines) Antenna Graphics with Dimensions TURBOROGUE: AOAD/M_T ----- / + \ <-- 0.128 L2 | + | <-- 0.110 L1 +--------------------------------------------------+ <-- 0.102 TCR | | | | | | | | +-+--------------------------------------------------+-+ <-- 0.038 +-------------------+-------------+--------------------+ <-- 0.035 BCR | | =| | +------x------+ <-- 0.000 ARP <-- 0.381 --> ARP: Antenna Reference Point L1 : L1 Phase Center L2 : L2 Phase Center TCR: Top of Chokering BCR: Bottom of Chokering