CAS100ATA Site Information Form (site log) International GNSS Service See Instructions at: https://ftp.igs.org/pub/station/general/sitelog_instr.txt 0. Form Prepared by (full name) : mohammad_choudhury Date Prepared : 2021-07-07 Report Type : UPDATE If Update: Previous Site Log : cas1_20210219.log Modified/Added Sections : 3.19,3.20 1. Site Identification of the GNSS Monument Site Name : Casey Four Character ID : CAS1 Monument Inscription : AUS100 IERS DOMES Number : 66011M001 CDP Number : NONE Monument Description : PLATE/STEEL Height of the Monument : Monument Foundation : ROCK Foundation Depth : Marker Description : PIN ON Stainless Steel Plate Date Installed : 1993-12-14T00:00Z Geologic Characteristic : BEDROCK Bedrock Type : METAMORPHIC Bedrock Condition : WEATHERED Fracture Spacing : Fault zones nearby : Distance/activity : Additional Information : (multiple lines) ARGN (Australian Regional GPS : Network) - Permanent GPS Tracking Network 2. Site Location Information City or Town : Casey State or Province : Australian Antarctic Territory (AAT) Country : Antarctica Tectonic Plate : ANTARCTIC Approximate Position (ITRF) X coordinate (m) : -901776.221 Y coordinate (m) : 2409383.497 Z coordinate (m) : -5816748.487 Latitude (N is +) : -661700.24 Longitude (E is +) : +1103110.92 Elevation (m,ellips.) : 22.6 Additional Information : The site is located at the Australian antarctic : research station Casey in Wilkes Land, : Australian Antarctic Territory. 3. GNSS Receiver Information 3.1 Receiver Type : AOA ICS-4000Z Satellite System : GPS Serial Number : C116 Firmware Version : 1.28.1 Elevation Cutoff Setting : 0 deg Date Installed : 1994-01-01T00:00Z Date Removed : 1996-01-27T00:00Z Temperature Stabiliz. : none Additional Information : 3.2 Receiver Type : AOA ICS-4000Z Satellite System : GPS Serial Number : C 127 Firmware Version : 3.2.33.1 Elevation Cutoff Setting : 0 deg Date Installed : 1996-01-27T02:30Z Date Removed : 1999-08-21T00:00Z Temperature Stabiliz. : none Additional Information : 3.3 Receiver Type : AOA ICS-4000Z Satellite System : GPS Serial Number : C 127 Firmware Version : 3.2.33.9 Elevation Cutoff Setting : 0 deg Date Installed : 1999-12-09T00:00Z Date Removed : 2000-02-05T00:00Z Temperature Stabiliz. : none Additional Information : 3.4 Receiver Type : AOA ICS-4000Z ACT Satellite System : GPS Serial Number : C122U Firmware Version : 3.3.32.3 Elevation Cutoff Setting : 0 deg Date Installed : 2000-02-05T00:00Z Date Removed : 2004-10-24T03:00Z Temperature Stabiliz. : none Additional Information : 3.5 Receiver Type : ASHTECH UZ-12 Satellite System : GPS Serial Number : ZR2200340002 Firmware Version : CN00 Elevation Cutoff Setting : 0 deg Date Installed : 2004-10-25T00:00Z Date Removed : 2008-12-02T23:59Z Temperature Stabiliz. : none Additional Information : 3.6 Receiver Type : LEICA GRX1200GGPRO Satellite System : GPS+GLO Serial Number : 356537 Firmware Version : 6.02 Elevation Cutoff Setting : 0 deg Date Installed : 2008-12-03T23:59Z Date Removed : 2009-11-12T23:59Z Temperature Stabiliz. : none Additional Information : 3.7 Receiver Type : LEICA GRX1200GGPRO Satellite System : GPS+GLO Serial Number : 356537 Firmware Version : 7.50 Elevation Cutoff Setting : 0 deg Date Installed : 2009-11-13T00:00Z Date Removed : 2010-05-04T00:00Z Temperature Stabiliz. : none Additional Information : 3.8 Receiver Type : LEICA GRX1200GGPRO Satellite System : GPS+GLO Serial Number : 356537 Firmware Version : 7.50/3.019 Elevation Cutoff Setting : 0 deg Date Installed : 2010-05-04T00:00Z Date Removed : 2011-02-01T23:45Z Temperature Stabiliz. : none Additional Information : ME upgrade due to GLONASS tracking problems. 3.9 Receiver Type : LEICA GRX1200GGPRO Satellite System : GPS+GLO Serial Number : 356537 Firmware Version : 8.01/3.019 Elevation Cutoff Setting : 0 deg Date Installed : 2011-02-01T23:45Z Date Removed : 2011-10-12T14:35Z Temperature Stabiliz. : none Additional Information : FW upgrade to fix datalogging issues 3.10 Receiver Type : LEICA GRX1200GGPRO Satellite System : GPS+GLO Serial Number : 356537 Firmware Version : 8.20/3.019 Elevation Cutoff Setting : 0 deg Date Installed : 2011-10-12T14:35Z Date Removed : 2013-12-10T00:00Z Temperature Stabiliz. : none Additional Information : FW upgrade to fix datalogging issues 3.11 Receiver Type : TRIMBLE NETR9 Satellite System : GPS+GLO+GAL+BDS+QZSS Serial Number : 5212K83358 Firmware Version : 4.81 Elevation Cutoff Setting : 0 deg Date Installed : 2013-12-11T03:00Z Date Removed : 2015-06-12T00:00Z Temperature Stabiliz. : none Additional Information : 3.12 Receiver Type : TRIMBLE NETR9 Satellite System : GPS+GLO+GAL+BDS+QZSS Serial Number : 5212K83358 Firmware Version : 5.01 Elevation Cutoff Setting : 0 deg Date Installed : 2015-06-12T00:00Z Date Removed : 2016-01-11T00:00Z Temperature Stabiliz. : none Additional Information : 3.13 Receiver Type : TRIMBLE NETR9 Satellite System : GPS+GLO+GAL+BDS+QZSS Serial Number : 5212K83358 Firmware Version : 5.10 Elevation Cutoff Setting : 0 deg Date Installed : 2016-01-11T00:00Z Date Removed : 2016-12-15T00:00Z Temperature Stabiliz. : none Additional Information : 3.14 Receiver Type : TRIMBLE NETR9 Satellite System : GPS+GLO+GAL+BDS+QZSS Serial Number : 5212K83358 Firmware Version : 5.15 Elevation Cutoff Setting : 0 deg Date Installed : 2016-12-15T00:00Z Date Removed : 2017-05-01T00:00Z Temperature Stabiliz. : none Additional Information : Firmware upgrade only 3.15 Receiver Type : TRIMBLE NETR9 Satellite System : GPS+GLO+GAL+BDS+QZSS Serial Number : 5212K83358 Firmware Version : 5.22 Elevation Cutoff Setting : 0 deg Date Installed : 2017-05-01T00:00Z Date Removed : 2018-07-18T01:00Z Temperature Stabiliz. : none Additional Information : Firmware upgrade only 3.16 Receiver Type : TRIMBLE NETR9 Satellite System : QZSS+GPS+GLO+GAL+BDS Serial Number : 5212K83358 Firmware Version : 5.33 Elevation Cutoff Setting : 0 deg Date Installed : 2018-07-18T01:00Z Date Removed : 2019-04-12T05:00Z Temperature Stabiliz. : none Additional Information : Firmware upgrade only 3.17 Receiver Type : TRIMBLE NETR9 Satellite System : GPS+GLO+GAL+BDS+QZSS Serial Number : 5212K83358 Firmware Version : 5.37 Elevation Cutoff Setting : 0 deg Date Installed : 2019-04-12T05:00Z Date Removed : 2020-04-03T05:20Z Temperature Stabiliz. : none Additional Information : Firmware upgrade only 3.18 Receiver Type : TRIMBLE NETR9 Satellite System : GPS+GLO+GAL+BDS+QZSS Serial Number : 5212K83358 Firmware Version : 5.44 Elevation Cutoff Setting : 0 deg Date Installed : 2020-04-03T05:20Z Date Removed : 2020-05-22T00:00Z Temperature Stabiliz. : none Additional Information : Firmware Upgrade Only 3.19 Receiver Type : SEPT POLARXS Satellite System : GPS+GLO+GAL+BDS+QZSS Serial Number : 3000358 Firmware Version : 2.9.6 Elevation Cutoff Setting : 0 deg Date Installed : 2020-05-22T00:00Z Date Removed : 2021-07-07T04:29Z Temperature Stabiliz. : none Additional Information : 3.20 Receiver Type : TRIMBLE ALLOY Satellite System : GPS+QZSS+GLO+GAL+BDS Serial Number : 5950R40131 Firmware Version : 6.10 Elevation Cutoff Setting : Date Installed : 2021-07-07T04:29Z Date Removed : CCYY-MM-DDThh:mmZ Temperature Stabiliz. : none Additional Information : 3.x Receiver Type : (A20, from rcvr_ant.tab; see instructions) Satellite System : (GPS+GLO+GAL+BDS+QZSS+SBAS) Serial Number : (A20, but note the first A5 is used in SINEX) Firmware Version : (A11) Elevation Cutoff Setting : (deg) Date Installed : (CCYY-MM-DDThh:mmZ) Date Removed : (CCYY-MM-DDThh:mmZ) Temperature Stabiliz. : (none or tolerance in degrees C) Additional Information : (multiple lines) 4. GNSS Antenna Information 4.1 Antenna Type : AOAD/M_T AUST Serial Number : 259 Antenna Reference Point : BPA Marker->ARP Up Ecc. (m) : 000.0010 Marker->ARP North Ecc(m) : 000.0000 Marker->ARP East Ecc(m) : 000.0000 Alignment from True N : 0 deg Antenna Radome Type : AUST Radome Serial Number : Antenna Cable Type : Antenna Cable Length : Date Installed : 1994-01-01T00:00Z Date Removed : 1997-12-09T09:15Z Additional Information : 4.2 Antenna Type : AOAD/M_T AUST Serial Number : 259 Antenna Reference Point : BPA Marker->ARP Up Ecc. (m) : 000.0010 Marker->ARP North Ecc(m) : 000.0000 Marker->ARP East Ecc(m) : 000.0000 Alignment from True N : 0 deg Antenna Radome Type : AUST Radome Serial Number : Antenna Cable Type : Antenna Cable Length : Date Installed : 1997-12-09T09:15Z Date Removed : 2013-12-10T00:00Z Additional Information : Radome replaced with same type 4.3 Antenna Type : LEIAR25.R3 LEIT Serial Number : 9310002 Antenna Reference Point : BPA Marker->ARP Up Ecc. (m) : 000.0000 Marker->ARP North Ecc(m) : 000.0000 Marker->ARP East Ecc(m) : 000.0000 Alignment from True N : 0 deg Antenna Radome Type : LEIT Radome Serial Number : Antenna Cable Type : LMR600 Antenna Cable Length : 250.0 m Date Installed : 2013-12-11T03:00Z Date Removed : CCYY-MM-DDThh:mmZ Additional Information : 4.x Antenna Type : (A20, from rcvr_ant.tab; see instructions) Serial Number : (A*, but note the first A5 is used in SINEX) Antenna Reference Point : (BPA/BCR/XXX from "antenna.gra"; see instr.) Marker->ARP Up Ecc. (m) : (F8.4) Marker->ARP North Ecc(m) : (F8.4) Marker->ARP East Ecc(m) : (F8.4) Alignment from True N : (deg; + is clockwise/east) Antenna Radome Type : (A4 from rcvr_ant.tab; see instructions) Radome Serial Number : Antenna Cable Type : (vendor & type number) Antenna Cable Length : (m) Date Installed : (CCYY-MM-DDThh:mmZ) Date Removed : (CCYY-MM-DDThh:mmZ) Additional Information : (multiple lines) 5. Surveyed Local Ties 5.1 Tied Marker Name : RM1 Tied Marker Usage : LOCAL CONTROL Tied Marker CDP Number : Tied Marker DOMES Number : Differential Components from GNSS Marker to the tied monument (ITRS) dx (m) : -13.0062 dy (m) : 0.2325 dz (m) : 2.9396 Accuracy (mm) : 1.0 mm Survey method : TRIANGULATION Date Measured : 2001-10-15T00:00Z Additional Information : 5.2 Tied Marker Name : RM2 Tied Marker Usage : LOCAL CONTROL Tied Marker CDP Number : Tied Marker DOMES Number : Differential Components from GNSS Marker to the tied monument (ITRS) dx (m) : -4.3406 dy (m) : -10.4272 dz (m) : -2.4219 Accuracy (mm) : 1.0 mm Survey method : TRIANGULATION Date Measured : 2001-10-15T00:00Z Additional Information : 5.3 Tied Marker Name : RM3 Tied Marker Usage : LOCAL CONTROL Tied Marker CDP Number : Tied Marker DOMES Number : Differential Components from GNSS Marker to the tied monument (ITRS) dx (m) : 4.7985 dy (m) : 7.5984 dz (m) : 1.6472 Accuracy (mm) : 1.0 mm Survey method : TRIANGULATION Date Measured : 2001-10-15T00:00Z Additional Information : 5.4 Tied Marker Name : RM1 Tied Marker Usage : LOCAL CONTROL Tied Marker CDP Number : Tied Marker DOMES Number : Differential Components from GNSS Marker to the tied monument (ITRS) dx (m) : -13.0064 dy (m) : 0.2299 dz (m) : 2.9394 Accuracy (mm) : 1.0 mm Survey method : TRIANGULATION Date Measured : 2004-10-15T00:00Z Additional Information : 5.5 Tied Marker Name : RM2 Tied Marker Usage : LOCAL CONTROL Tied Marker CDP Number : Tied Marker DOMES Number : Differential Components from GNSS Marker to the tied monument (ITRS) dx (m) : -4.3407 dy (m) : -10.4295 dz (m) : -2.4237 Accuracy (mm) : 1.0 mm Survey method : TRIANGULATION Date Measured : 2004-10-15T00:00Z Additional Information : 5.6 Tied Marker Name : RM3 Tied Marker Usage : LOCAL CONTROL Tied Marker CDP Number : Tied Marker DOMES Number : Differential Components from GNSS Marker to the tied monument (ITRS) dx (m) : 4.7974 dy (m) : 7.598 dz (m) : 1.6464 Accuracy (mm) : 1.0 mm Survey method : TRIANGULATION Date Measured : 2004-10-15T00:00Z Additional Information : 5.x Tied Marker Name : Tied Marker Usage : (SLR/VLBI/LOCAL CONTROL/FOOTPRINT/etc) Tied Marker CDP Number : (A4) Tied Marker DOMES Number : (A9) Differential Components from GNSS Marker to the tied monument (ITRS) dx (m) : (m) dy (m) : (m) dz (m) : (m) Accuracy (mm) : (mm) Survey method : (GPS CAMPAIGN/TRILATERATION/TRIANGULATION/etc) Date Measured : (CCYY-MM-DDThh:mmZ) Additional Information : (multiple lines) 6. Frequency Standard 6.1 Standard Type : EXTERNAL RUBIDIUM Input Frequency : 5 MHz Effective Dates : 1994-07-11/1998-01-08 Notes : 6.2 Standard Type : INTERNAL Input Frequency : 5 MHz Effective Dates : 1998-01-09/CCYY-MM-DD Notes : Effective at 1998-01-09T02:52Z exactly 6.x Standard Type : (INTERNAL or EXTERNAL H-MASER/CESIUM/etc) Input Frequency : (if external) Effective Dates : (CCYY-MM-DD/CCYY-MM-DD) Notes : (multiple lines) 7. Collocation Information 7.x Instrumentation Type : (GPS/GLONASS/DORIS/PRARE/SLR/VLBI/TIME/etc) Status : (PERMANENT/MOBILE) Effective Dates : (CCYY-MM-DD/CCYY-MM-DD) Notes : (multiple lines) 8. Meteorological Instrumentation 8.1.x Humidity Sensor Model : Manufacturer : Serial Number : Data Sampling Interval : (sec) Accuracy (% rel h) : (% rel h) Aspiration : (UNASPIRATED/NATURAL/FAN/etc) Height Diff to Ant : (m) Calibration date : (CCYY-MM-DD) Effective Dates : (CCYY-MM-DD/CCYY-MM-DD) Notes : (multiple lines) 8.2.x Pressure Sensor Model : Manufacturer : Serial Number : Data Sampling Interval : (sec) Accuracy : (hPa) Height Diff to Ant : (m) Calibration date : (CCYY-MM-DD) Effective Dates : (CCYY-MM-DD/CCYY-MM-DD) Notes : (multiple lines) 8.3.x Temp. Sensor Model : Manufacturer : Serial Number : Data Sampling Interval : (sec) Accuracy : (deg C) Aspiration : (UNASPIRATED/NATURAL/FAN/etc) Height Diff to Ant : (m) Calibration date : (CCYY-MM-DD) Effective Dates : (CCYY-MM-DD/CCYY-MM-DD) Notes : (multiple lines) 8.4.x Water Vapor Radiometer : Manufacturer : Serial Number : Distance to Antenna : (m) Height Diff to Ant : (m) Calibration date : (CCYY-MM-DD) Effective Dates : (CCYY-MM-DD/CCYY-MM-DD) Notes : (multiple lines) 8.5.x Other Instrumentation : (multiple lines) 9. Local Ongoing Conditions Possibly Affecting Computed Position 9.1.x Radio Interferences : (TV/CELL PHONE ANTENNA/RADAR/etc) Observed Degradations : (SN RATIO/DATA GAPS/etc) Effective Dates : (CCYY-MM-DD/CCYY-MM-DD) Additional Information : (multiple lines) 9.2.x Multipath Sources : (METAL ROOF/DOME/VLBI ANTENNA/etc) Effective Dates : (CCYY-MM-DD/CCYY-MM-DD) Additional Information : (multiple lines) 9.3.x Signal Obstructions : (TREES/BUILDINGS/etc) Effective Dates : (CCYY-MM-DD/CCYY-MM-DD) Additional Information : (multiple lines) 10. Local Episodic Effects Possibly Affecting Data Quality 10.x Date : (CCYY-MM-DD/CCYY-MM-DD) Event : (TREE CLEARING/CONSTRUCTION/etc) 11. On-Site, Point of Contact Agency Information Agency : Geoscience Australia Preferred Abbreviation : Mailing Address : GPO Box 378 : Canberra ACT 2601 : AUSTRALIA Primary Contact Contact Name : Ryan Ruddick Telephone (primary) : +61 2 6249 9426 Telephone (secondary) : +61 2 6249 9111 Fax : E-mail : geodesy@ga.gov.au Secondary Contact Contact Name : Nicholas Brown Telephone (primary) : +61 2 6249 9831 Telephone (secondary) : +61 2 6249 9111 Fax : E-mail : geodesy@ga.gov.au Additional Information : 12. Responsible Agency (if different from 11.) Agency : Geoscience Australia Preferred Abbreviation : Mailing Address : GPO Box 378 : Canberra ACT 2601 : AUSTRALIA Primary Contact Contact Name : Ryan Ruddick Telephone (primary) : +61 2 6249 9426 Telephone (secondary) : +61 2 6249 9111 Fax : E-mail : geodesy@ga.gov.au Secondary Contact Contact Name : Telephone (primary) : Telephone (secondary) : Fax : E-mail : Additional Information : 13. More Information Primary Data Center : GA Secondary Data Center : CDDIS URL for More Information : http://www.ga.gov.au Hardcopy on File Site Map : Y Site Diagram : Y Horizon Mask : Y Monument Description : Y Site Pictures : Y Additional Information : Antenna Graphics with Dimensions (insert text graphic from file antenna.gra)