ALIC00AUS Site Information Form (site log) International GNSS Service See Instructions at: https://files.igs.org/pub/station/general/sitelog_instr.txt 0. Form Prepared by (full name) : mohammad_choudhury Date Prepared : 2022-12-14 Report Type : UPDATE If Update: Previous Site Log : (ssss_ccyymmdd.log) Modified/Added Sections : (n.n,n.n,...) 1. Site Identification of the GNSS Monument Site Name : Alice Springs AU012 Four Character ID : ALIC Monument Inscription : National Geodetic Fiducial Ntwk (AUSLIG) AU012 IERS DOMES Number : 50137M001 CDP Number : None Monument Description : Concrete pillar/stainless steel plate Height of the Monument : 0.5 m Monument Foundation : Bedrock Foundation Depth : Marker Description : Intersection of plate with spigot Date Installed : 1992-08-12T00:00Z Geologic Characteristic : BEDROCK Bedrock Type : METAMORPHIC Bedrock Condition : WEATHERED Fracture Spacing : Fault zones nearby : NO Distance/activity : Additional Information : Monument is a 600mm dia concrete pillar, 0.5 : metres above ground surface, 5/8 inch spigot : thread 2. Site Location Information City or Town : Alice Springs State or Province : Northern Territory Country : Australia Tectonic Plate : AUSTRALIAN Approximate Position (ITRF) X coordinate (m) : -4052052.7352 Y coordinate (m) : 4212835.9833 Z coordinate (m) : -2545104.5853 Latitude (N is +) : -234012.40 Longitude (E is +) : +1335307.88 Elevation (m,ellips.) : 603.2 Additional Information : ARGN (Australian Regional GPS Network) 3. GNSS Receiver Information 3.1 Receiver Type : AOA ICS-4000Z Satellite System : GPS Serial Number : C128 Firmware Version : 3.2.33.1 Elevation Cutoff Setting : 0 deg Date Installed : 1994-05-15T00:00Z Date Removed : 1999-07-31T01:00Z Temperature Stabiliz. : none Additional Information : 3.2 Receiver Type : AOA ICS-4000Z Satellite System : GPS Serial Number : C128 Firmware Version : 3.2.32.9 Elevation Cutoff Setting : 0 deg Date Installed : 1999-07-31T01:00Z Date Removed : 2000-01-14T01:50Z Temperature Stabiliz. : none Additional Information : Upgrade of firmware to avoid GPS week 3.3 Receiver Type : AOA SNR-12 ACT Satellite System : GPS Serial Number : C102U Firmware Version : 3.3.32.3 Elevation Cutoff Setting : 0 deg Date Installed : 2000-01-14T02:00Z Date Removed : 2000-01-24T01:00Z Temperature Stabiliz. : none Additional Information : This receiver is AC power only 3.4 Receiver Type : AOA ICS-4000Z ACT Satellite System : GPS Serial Number : C126U Firmware Version : 3.3.32.3 Elevation Cutoff Setting : 0 deg Date Installed : 2000-01-24T02:15Z Date Removed : 2003-10-22T23:59Z Temperature Stabiliz. : none Additional Information : This receiver is AC/DC 3.5 Receiver Type : ASHTECH UZ-12 Satellite System : GPS Serial Number : UC2200302004 Firmware Version : ZC00 Elevation Cutoff Setting : 0 deg Date Installed : 2003-10-23T00:00Z Date Removed : 2008-04-15T23:59Z Temperature Stabiliz. : none Additional Information : The Old AOA Rx still remains on site as a backup : to the Micro Z 3.6 Receiver Type : LEICA GRX1200GGPRO Satellite System : GPS+GLO Serial Number : 355318 Firmware Version : 5.62 Elevation Cutoff Setting : 0 deg Date Installed : 2008-04-16T00:00Z Date Removed : 2008-09-16T23:59Z Temperature Stabiliz. : none Additional Information : 3.7 Receiver Type : LEICA GRX1200GGPRO Satellite System : GPS+GLO Serial Number : 355318 Firmware Version : 6.00 Elevation Cutoff Setting : 0 deg Date Installed : 2008-09-17T00:00Z Date Removed : 2009-07-24T00:00Z Temperature Stabiliz. : none Additional Information : 3.8 Receiver Type : LEICA GRX1200GGPRO Satellite System : GPS+GLO Serial Number : 355318 Firmware Version : 7.50 Elevation Cutoff Setting : 0 deg Date Installed : 2009-07-24T00:00Z Date Removed : 2010-05-06T00:00Z Temperature Stabiliz. : none Additional Information : The tracking was changed from C2 or P2, to P2 : only at 2009-07-30T00:00Z Tracking was change to : All in view at 2009-09-09T00:00Z 3.9 Receiver Type : LEICA GRX1200GGPRO Satellite System : GPS+GLO Serial Number : 355318 Firmware Version : 7.50/3.019 Elevation Cutoff Setting : 0 deg Date Installed : 2010-05-06T00:00Z Date Removed : 2011-06-26T23:59Z Temperature Stabiliz. : none Additional Information : ME upgrade due to GLONASS tracking problem. 3.10 Receiver Type : LEICA GRX1200GGPRO Satellite System : GPS+GLO Serial Number : 355318 Firmware Version : 8.20/3.019 Elevation Cutoff Setting : 0 deg Date Installed : 2011-06-27T00:00Z Date Removed : 2013-03-08T00:00Z Temperature Stabiliz. : none Additional Information : 3.11 Receiver Type : LEICA GRX1200GGPRO Satellite System : GPS+GLO Serial Number : 355318 Firmware Version : 8.51/3.019 Elevation Cutoff Setting : 0 deg Date Installed : 2013-03-08T00:00Z Date Removed : 2013-07-08T00:45Z Temperature Stabiliz. : none Additional Information : 3.12 Receiver Type : LEICA GRX1200GGPRO Satellite System : GPS+GLO Serial Number : 355318 Firmware Version : 8.71/3.822 Elevation Cutoff Setting : 0 deg Date Installed : 2013-07-08T00:45Z Date Removed : 2016-02-04T00:00Z Temperature Stabiliz. : none Additional Information : 3.13 Receiver Type : LEICA GR25 Satellite System : GPS+GLO+GAL+BDS+QZSS Serial Number : 1830439 Firmware Version : 6.521 Elevation Cutoff Setting : 0 deg Date Installed : 2016-02-04T00:00Z Date Removed : 2016-04-14T00:48Z Temperature Stabiliz. : none Additional Information : 3.14 Receiver Type : LEICA GR25 Satellite System : GPS+GLO+GAL+BDS+QZSS Serial Number : 1830439 Firmware Version : 3.22.1818/6.522 Elevation Cutoff Setting : 0 deg Date Installed : 2016-04-14T00:48Z Date Removed : 2016-09-22T00:00Z Temperature Stabiliz. : none Additional Information : 3.15 Receiver Type : LEICA GR25 Satellite System : GPS+GLO+GAL+BDS+QZSS Serial Number : 1830439 Firmware Version : 4.00.335/6.522 Elevation Cutoff Setting : 0 deg Date Installed : 2016-09-22T00:00Z Date Removed : 2016-12-13T00:00Z Temperature Stabiliz. : none Additional Information : 3.16 Receiver Type : LEICA GR25 Satellite System : GPS+GLO+GAL+BDS+QZSS Serial Number : 1830439 Firmware Version : 4.02.386/6.522 Elevation Cutoff Setting : 0 deg Date Installed : 2016-12-13T00:00Z Date Removed : 2017-01-31T00:00Z Temperature Stabiliz. : none Additional Information : 3.17 Receiver Type : LEICA GR25 Satellite System : GPS+GLO+GAL+BDS+QZSS Serial Number : 1830439 Firmware Version : 4.10.598/6.523 Elevation Cutoff Setting : 0 deg Date Installed : 2017-01-31T00:00Z Date Removed : 2017-02-23T00:00Z Temperature Stabiliz. : none Additional Information : 3.18 Receiver Type : LEICA GR25 Satellite System : GPS+GLO+GAL+BDS+QZSS Serial Number : 1830439 Firmware Version : 4.11.606/6.523 Elevation Cutoff Setting : 0 deg Date Installed : 2017-02-23T00:00Z Date Removed : 2018-05-21T00:35Z Temperature Stabiliz. : none Additional Information : 3.19 Receiver Type : LEICA GR25 Satellite System : GPS+BDS+GLO+QZSS+GAL Serial Number : 1830439 Firmware Version : 4.20.232/6.524 Elevation Cutoff Setting : 0 deg Date Installed : 2018-05-21T00:35Z Date Removed : 2018-07-02T23:59Z Temperature Stabiliz. : none Additional Information : Firmware update only 3.20 Receiver Type : LEICA GR25 Satellite System : GPS+QZSS+GLO+GAL+BDS Serial Number : 1830439 Firmware Version : 4.20.232/7.300 Elevation Cutoff Setting : 0 deg Date Installed : 2018-07-03T00:00Z Date Removed : 2019-03-18T00:00Z Temperature Stabiliz. : none Additional Information : Firmware update only 3.21 Receiver Type : LEICA GR25 Satellite System : GPS+GLO+GAL+BDS+QZSS Serial Number : 1830439 Firmware Version : 4.30.063/6.525 Elevation Cutoff Setting : 0 deg Date Installed : 2019-03-18T00:00Z Date Removed : 2019-10-22T03:13Z Temperature Stabiliz. : none Additional Information : Firmware upgrade only 3.22 Receiver Type : LEICA GR25 Satellite System : GPS+GLO+GAL+BDS+QZSS Serial Number : 1830439 Firmware Version : 4.31.101 Elevation Cutoff Setting : 0 deg Date Installed : 2019-10-22T03:13Z Date Removed : 2020-09-30T23:59Z Temperature Stabiliz. : none Additional Information : 3.23 Receiver Type : LEICA GR25 Satellite System : GPS+GLO+GAL+BDS+QZSS Serial Number : 1830439 Firmware Version : 4.31/6.525 Elevation Cutoff Setting : 0 deg Date Installed : 2020-10-01T00:00Z Date Removed : 2020-12-10T00:00Z Temperature Stabiliz. : none Additional Information : Fixed firmware version in file headers. 3.24 Receiver Type : SEPT POLARX5 Satellite System : GPS+QZSS+GLO+GAL+BDS Serial Number : 3061704 Firmware Version : 5.3.2 Elevation Cutoff Setting : 0 deg Date Installed : 2020-12-10T00:00Z Date Removed : 2021-02-25T23:43Z Temperature Stabiliz. : none Additional Information : 3.25 Receiver Type : SEPT POLARX5 Satellite System : GPS+QZSS+GLO+GAL+BDS Serial Number : 3061704 Firmware Version : 5.4.0 Elevation Cutoff Setting : 0 deg Date Installed : 2021-02-25T23:43Z Date Removed : 2022-11-01T00:01Z Temperature Stabiliz. : none Additional Information : 3.26 Receiver Type : SEPT POLARX5 Satellite System : GPS+QZSS+GLO+GAL+BDS Serial Number : 3061704 Firmware Version : 5.5.0 Elevation Cutoff Setting : 0 deg Date Installed : 2022-11-01T00:01Z Date Removed : CCYY-MM-DDThh:mmZ Temperature Stabiliz. : none Additional Information : Firmware upgrade only 3.x Receiver Type : (A20, from rcvr_ant.tab; see instructions) Satellite System : (GPS+GLO+GAL+BDS+QZSS+SBAS) Serial Number : (A20, but note the first A5 is used in SINEX) Firmware Version : (A11) Elevation Cutoff Setting : (deg) Date Installed : (CCYY-MM-DDThh:mmZ) Date Removed : (CCYY-MM-DDThh:mmZ) Temperature Stabiliz. : (none or tolerance in degrees C) Additional Information : (multiple lines) 4. GNSS Antenna Information 4.1 Antenna Type : AOAD/M_T AUST Serial Number : 318 Antenna Reference Point : BPA Marker->ARP Up Ecc. (m) : 000.0070 Marker->ARP North Ecc(m) : 000.0000 Marker->ARP East Ecc(m) : 000.0000 Alignment from True N : 0 deg Antenna Radome Type : AUST Radome Serial Number : Antenna Cable Type : Antenna Cable Length : Date Installed : 1994-05-15T00:00Z Date Removed : 2003-06-15T03:30Z Additional Information : Radome was damaged at an unknown time during : this period. 4.2 Antenna Type : AOAD/M_T NONE Serial Number : 318 Antenna Reference Point : BPA Marker->ARP Up Ecc. (m) : 000.0070 Marker->ARP North Ecc(m) : 000.0000 Marker->ARP East Ecc(m) : 000.0000 Alignment from True N : 0 deg Antenna Radome Type : NONE Radome Serial Number : Antenna Cable Type : Antenna Cable Length : Date Installed : 2003-06-15T03:30Z Date Removed : 2011-07-20T00:00Z Additional Information : Damaged radome was removed. 4.3 Antenna Type : LEIAR25.R3 NONE Serial Number : 09370001 Antenna Reference Point : BPA Marker->ARP Up Ecc. (m) : 000.0015 Marker->ARP North Ecc(m) : 000.0000 Marker->ARP East Ecc(m) : 000.0000 Alignment from True N : 0 deg Antenna Radome Type : NONE Radome Serial Number : Antenna Cable Type : LMR400 Antenna Cable Length : 81.0 m Date Installed : 2011-07-20T00:00Z Date Removed : CCYY-MM-DDThh:mmZ Additional Information : 4.x Antenna Type : (A20, from rcvr_ant.tab; see instructions) Serial Number : (A*, but note the first A5 is used in SINEX) Antenna Reference Point : (BPA/BCR/XXX from "antenna.gra"; see instr.) Marker->ARP Up Ecc. (m) : (F8.4) Marker->ARP North Ecc(m) : (F8.4) Marker->ARP East Ecc(m) : (F8.4) Alignment from True N : (deg; + is clockwise/east) Antenna Radome Type : (A4 from rcvr_ant.tab; see instructions) Radome Serial Number : Antenna Cable Type : (vendor & type number) Antenna Cable Length : (m) Date Installed : (CCYY-MM-DDThh:mmZ) Date Removed : (CCYY-MM-DDThh:mmZ) Additional Information : (multiple lines) 5. Surveyed Local Ties 5.1 Tied Marker Name : RM1 Tied Marker Usage : Tied Marker CDP Number : Tied Marker DOMES Number : Differential Components from GNSS Marker to the tied monument (ITRS) dx (m) : -15.366 dy (m) : -9.632 dz (m) : 9.099 Accuracy (mm) : 1.0 mm Survey method : Date Measured : 1992-08-12T00:00Z Additional Information : 5.2 Tied Marker Name : RM2 Tied Marker Usage : Tied Marker CDP Number : Tied Marker DOMES Number : Differential Components from GNSS Marker to the tied monument (ITRS) dx (m) : 6.89 dy (m) : -0.437 dz (m) : -9.874 Accuracy (mm) : 1.0 mm Survey method : Date Measured : 1992-08-12T00:00Z Additional Information : 5.3 Tied Marker Name : RM3 Tied Marker Usage : Tied Marker CDP Number : Tied Marker DOMES Number : Differential Components from GNSS Marker to the tied monument (ITRS) dx (m) : 4.399 dy (m) : 15.434 dz (m) : 18.074 Accuracy (mm) : 1.0 mm Survey method : Date Measured : 1992-08-12T00:00Z Additional Information : 5.x Tied Marker Name : Tied Marker Usage : (SLR/VLBI/LOCAL CONTROL/FOOTPRINT/etc) Tied Marker CDP Number : (A4) Tied Marker DOMES Number : (A9) Differential Components from GNSS Marker to the tied monument (ITRS) dx (m) : (m) dy (m) : (m) dz (m) : (m) Accuracy (mm) : (mm) Survey method : (GPS CAMPAIGN/TRILATERATION/TRIANGULATION/etc) Date Measured : (CCYY-MM-DDThh:mmZ) Additional Information : (multiple lines) 6. Frequency Standard 6.1 Standard Type : INTERNAL Input Frequency : Effective Dates : 1994-05-15/CCYY-MM-DD Notes : 6.x Standard Type : (INTERNAL or EXTERNAL H-MASER/CESIUM/etc) Input Frequency : (if external) Effective Dates : (CCYY-MM-DD/CCYY-MM-DD) Notes : (multiple lines) 7. Collocation Information 7.x Instrumentation Type : (GPS/GLONASS/DORIS/PRARE/SLR/VLBI/TIME/etc) Status : (PERMANENT/MOBILE) Effective Dates : (CCYY-MM-DD/CCYY-MM-DD) Notes : (multiple lines) 8. Meteorological Instrumentation 8.1.1 Humidity Sensor Model : PAROSCIENTIFIC MET3A Manufacturer : Paroscientific, Inc. Serial Number : 98850 Data Sampling Interval : 30 sec Accuracy (% rel h) : 2.00 Aspiration : FAN Height Diff to Ant : 2.4 m Calibration date : (CCYY-MM-DD) Effective Dates : 2006-03-29/CCYY-MM-DD Notes : 8.1.x Humidity Sensor Model : Manufacturer : Serial Number : Data Sampling Interval : (sec) Accuracy (% rel h) : (% rel h) Aspiration : (UNASPIRATED/NATURAL/FAN/etc) Height Diff to Ant : (m) Calibration date : (CCYY-MM-DD) Effective Dates : (CCYY-MM-DD/CCYY-MM-DD) Notes : (multiple lines) 8.2.1 Pressure Sensor Model : PAROSCIENTIFIC MET3A Manufacturer : Paroscientific, Inc. Serial Number : 98850 Data Sampling Interval : 30 sec Accuracy : 0.10 hPa Height Diff to Ant : 2.4 m Calibration date : (CCYY-MM-DD) Effective Dates : 2006-03-29/CCYY-MM-DD Notes : 8.2.x Pressure Sensor Model : Manufacturer : Serial Number : Data Sampling Interval : (sec) Accuracy : (hPa) Height Diff to Ant : (m) Calibration date : (CCYY-MM-DD) Effective Dates : (CCYY-MM-DD/CCYY-MM-DD) Notes : (multiple lines) 8.3.1 Temp. Sensor Model : PAROSCIENTIFIC MET3A Manufacturer : Paroscientific, Inc. Serial Number : 98850 Data Sampling Interval : 30 sec Accuracy : 0.50 deg C Aspiration : FAN Height Diff to Ant : 2.4 m Calibration date : Effective Dates : 2006-03-29/CCYY-MM-DD Notes : 8.3.x Temp. Sensor Model : Manufacturer : Serial Number : Data Sampling Interval : (sec) Accuracy : (deg C) Aspiration : (UNASPIRATED/NATURAL/FAN/etc) Height Diff to Ant : (m) Calibration date : (CCYY-MM-DD) Effective Dates : (CCYY-MM-DD/CCYY-MM-DD) Notes : (multiple lines) 8.4.x Water Vapor Radiometer : Manufacturer : Serial Number : Distance to Antenna : (m) Height Diff to Ant : (m) Calibration date : (CCYY-MM-DD) Effective Dates : (CCYY-MM-DD/CCYY-MM-DD) Notes : (multiple lines) 8.5.x Other Instrumentation : (multiple lines) 9. Local Ongoing Conditions Possibly Affecting Computed Position 9.1.x Radio Interferences : (TV/CELL PHONE ANTENNA/RADAR/etc) Observed Degradations : (SN RATIO/DATA GAPS/etc) Effective Dates : (CCYY-MM-DD/CCYY-MM-DD) Additional Information : (multiple lines) 9.2.x Multipath Sources : (METAL ROOF/DOME/VLBI ANTENNA/etc) Effective Dates : (CCYY-MM-DD/CCYY-MM-DD) Additional Information : (multiple lines) 9.3.x Signal Obstructions : (TREES/BUILDINGS/etc) Effective Dates : (CCYY-MM-DD/CCYY-MM-DD) Additional Information : (multiple lines) 10. Local Episodic Effects Possibly Affecting Data Quality 10.1 Date : 2011-07-20/2011-07-20 Event : TREE CLEARING 10.x Date : (CCYY-MM-DD/CCYY-MM-DD) Event : (TREE CLEARING/CONSTRUCTION/etc) 11. On-Site, Point of Contact Agency Information Agency : Geoscience Australia Preferred Abbreviation : Mailing Address : GPO Box 378 : Canberra ACT 2601 : AUSTRALIA : Canberra : 2601 : Australia Primary Contact Contact Name : Geoscience Australia Telephone (primary) : +61 2 6249 9004 Telephone (secondary) : +61 2 6249 9111 Fax : E-mail : gnss@ga.gov.au Secondary Contact Contact Name : Telephone (primary) : Telephone (secondary) : Fax : E-mail : Additional Information : 12. Responsible Agency (if different from 11.) Agency : Geoscience Australia Preferred Abbreviation : Mailing Address : GPO Box 378 : Canberra ACT 2601 : AUSTRALIA : Canberra : 2601 : Australia Primary Contact Contact Name : Geoscience Australia Telephone (primary) : +61 2 6249 9004 Telephone (secondary) : +61 2 6249 9111 Fax : E-mail : gnss@ga.gov.au Secondary Contact Contact Name : Telephone (primary) : Telephone (secondary) : Fax : E-mail : Additional Information : 13. More Information Primary Data Center : GA Secondary Data Center : CDDIS URL for More Information : http://www.ga.gov.au Hardcopy on File Site Map : Y Site Diagram : Y Horizon Mask : Y Monument Description : Y Site Pictures : Y Additional Information : Antenna Graphics with Dimensions (insert text graphic from file antenna.gra)